QUAD OC3/STM1 SFP UNI/NNI CLEI This card may be used in 7470 MSP R6.0 - R9.1 or 7670 ESE R2.2 - R5.X systems. The quad OC3/STM1 UNI/NNI Card is a ATM interface card operating at the SONET/SDH OC3/STM1 rate of 155 Mbps per port. This card is compliant to the requirements of the ATM Forum UNI Specification (Version 3.1) and the ATM Forum B-ICI Specification (Version 2.0). The card is shipped without the optical or electrical physical interface and requires one or more of the following parts to be installed before the card is functional: 90-9764-01 (OC3/STM1 MMF SFP), 90-9764-02 (OC3/STM1 IR SFP), 90-9764-03 (OC3/STM1 LR SFP) or 90-9764-04 (STM1 ELEC SFP). Note that the full set of SFP functions are only available in 7470 MSP R8.0-R9.1 or 7670 ESE R4.0-R5.1; in earlier releases the cards operate in 'transparency mode' and do not have access to the full set of SFP functions. One of the following adaptor cables must also be ordered, depending on the physical connector type required: 90-9771-01 (SINGLE MODE LC TO SC CONVERSION CABLE), 90-9771-02 (SINGLE MODE LC TO FC CONVERSION CABLE), 90-9771-03 (MULTIMODE LC TO SC CONVERSION CABLE), 90-9772-01 (BNC CONVERSION CABLE FOR ELEC SFP) or 90-9772-02 (SMZ CONVERSION CABLE FOR ELEC SFP).

8 PORT DS3 CR CARD clei The 8 port DS3 ATM Card is an 8 port card. Each port is both a UNI and NNI DS3 ATM interface operating at 45Mbps. Each interface has dual coax BNC connectors with a range of 450 feet. The DS3 card is fully compliant to the mandatory requirements of the ATM Forum UNI specification (version 3.1) and the ATM Forum B-ICI specification (version 2.0). This card is also supported in ESE R2.0.

CR/IMA MODULE FOR T1/E1 MS CARDS CLEI This optional, field-installable module provides T1/E1 Cell Relay functionality, enabling the 32 port T1/E1 multi-service card (7670 ESE) or 16 port T1/E1 MS card (7470 MSP) to deliver both Circuit Emulation and Cell Relay services. Cell Relay services are provisionable per DS1/E1 circuit. Up to 16 IMA groups are supported per module when used with the 32 port T1/E1 MS card, or 8 IMA groups per module when used with the 16 port T1/E1 MS card. The IMA implementation is compliant to the ATM Forum IMA specification Version 1.0 or 1.1. IMA v1.0 or v1.1 is configurable on a per T1 or per E1 basis.

DB78 TO DB78 CABLE (16 COAX) This cable is used to connect the 7470 8 port DS3 CR card to the 8 port 75 Ohm BNC distribution panel.

DS3 8 PORT 75 OHM BNC DIST. PANEL clei This distribution panel provides 8 external 75 Ohm BNC ports and is to be used with the 8 port DS3 CR card (90-8975-11). The panel is a 1 vertical unit (VU) high rack-mountable device. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

SGL MODE SC-SC FIBER - 4P 0C3/STM1 IR-LR This cable is used to connect the quad OC3/STM1 IR/LR CR optical card to a patch panel. It consists of a 8-fibre bundle (4 Tx and 4 Rx) of SC/SC single mode fibres. Individual SC to SC duplex (Rx-Tx) fibres may be used instead of this part. Approximate length: 10 feet.

MULTI MODE SC-SC FIBER - 4P OC3/STM1 MMF This cable is used to connect the quad OC3/STM1 MMF optical CR card to a patch panel. It consists of a 8-fibre bundle (4 Tx and 4 Rx) of SC/SC multi-mode fibres. Individual SC to SC duplex (Rx-Tx) fibres may be used instead of this part. Approximate length: 10 feet.

SMZ TO BNC 75OHM CABLE - 4P OC3/STM1 ELE This cable is used to connect the quad OC3/STM1 Electrical CR card to a patch panel. It consists of an 8xSMZ-to-BNC coaxial bundle. Individual SMZ-to-BNZ coaxial cables may be used instead of this part. Approximate length: 10 feet.

CTL TO INTEGRATED CTL CONVERT KIT The Control to Integrated Control conversion kit is used to convert a 7470 Control card to an Integrated Control card. The kit contains the password to enable the conversion and instructions for installation. This kit must be executed during an upgrade process prior to installing a release that is greater than Release 7. Integrated control software is mandatory for all 7470 systems operating above Release 7.0. The Integrated Control Card software required for the conversion is not included in this kit and must be obtained from the Alcatel TAC and TAC must be involved in any upgrade that requires this kit.

3-PORT DS3 FRAME PROCESSING CARD CLEI The triple port 3/1/0 Frame Processing Card provides a standards-compliant DS3 interface to the 7470 MSP and 7670 RSP ESE systems. The DS3 FP Card supports Frame Relay services. The Frame Processor card can support up to 512 streams. Each stream is made up of one DS3, one T1, or nxDS0 (1 to 24 for T1). This interface will perform standards-based frame switching network-interworking or service-interworking. Requires adapter card 90-7307-01 for use in the 7670 ESE. This card requires MAU 90-2322-02 for deployment in 7470 PS-2 shelf or MAU 90-7308-02 for deployment in 7670 ESE shelf. The 90-2322-01 and 90-7308-02 MAUs are not shipped with the DS3 FP card and each must be ordered separately. This assembly contains a Telcordia CLEI (Common Language Equipment Identifier) label.

VOP CARD 16 PORT T1/E1 clei The 16 port T1/E1 Voice over Packet(VoP) card provides voiceband services such as compression, echo cancellation and silence suppression on a per channel basis. The VoP card transports voiceband data (voice, modem, fax) across the ATM network via ITU-T standard AAL2. Basic voiceband processing (echo cancellation, A-law <-> mu-law conversion, . . .) is also supported for channels configured for AAL1. The supported Codes are G.711, G.726,and G.729A/B. Channel licenses for G.729A/B must be purchased separately (90-9729-02). This card also supports Fax and Modem bypass functionality. Due to power supply and cooling considerations, the 16-port T1/E1 VoP card (Voice over Packet) cannot be installed in a version 1 Peripheral shelf (part number 90-2190-01).

VOP 16 PORT G.729A/B CHNL LICENSE This channel license grants the bearer the right to operate the G.729 A Voice Coder on any or all channels on ONE 16 port VoP card in a 7470 system. A channel license is required for each line card purchased.

OC3/STM1 MMF SFP clei 1-port OC-3/STM-1 SONET/SDH Optics Module, MM, 1310 nm, LC Connector. Can be used in the Quad OC3/STM1 SFP Cell Relay card (90-8687-25) or OC3/STM1 1:N Working I/O (90-9785-02) (in ESE R5.X) or OC3/STM1 1:N Protecting I/O (90-9785-03) (in ESE R5.X). This unit is equipped with a Class 1 laser.

OC3/STM1 IR SFP clei 1-port OC-3/STM-1 SONET/SDH Optics Module, IR-1 / I-1, 1310 nm, LC Connector. Can be used in the Quad OC3/STM1 SFP Cell Relay card (90-8687-25) or OC3/STM1 1:N Working I/O (90-9785-02) (in ESE R5.X) or OC3/STM1 1:N Protecting I/O (90-9785-03) (in ESE R5.X). This unit is equipped with a Class 1 laser.

OC3/STM1 LR SFP clei 1-port OC-3/STM-1 SONET/SDH Optics Module, LR-1 / L-1.1, 1310 nm, LC Connector. Can be used in the Quad OC3/STM1 SFP Cell Relay card (90-8687-25) or OC3/STM1 1:N Working I/O (90-9785-02) (in ESE R5.X) or OC3/STM1 1:N Protecting I/O (90-9785-03) (in ESE R5.X). This unit is equipped with a Class 1 laser.

STM1 ELEC SFP 1-port STM-1 SDH Electrical Module, 1.0/2.3 Coaxial Connector (Type A Coupling). Can be used in the Quad OC3/STM1 SFP Cell Relay card (90-8687-25) or OC3/STM1 1:N Working I/O (90-9785-02) (in ESE R5.X) or OC3/STM1 1:N Protecting I/O (90-9785-03) (in ESE R5.X).

SINGLE MODE LC TO SC CONVERSION CABLE A 1 meter duplex single mode LC to SC conversion cable. Used with the Quad OC3/STM1 SFP Cell Relay card or the OC3/STM1 Working I/O (90-9785-02) to adapt the SFP connector to existing cable connectors.

SINGLE MODE LC TO FC CONVERSION CABLE A 1 meter duplex single mode LC to FC conversion cable. . Used with the Quad OC3/STM1 SFP Cell Relay card or the OC3/STM1 Working I/O (90-9785-02) to adapt the SFP connector to existing cable connectors.

MULTIMODE LC TO SC CONVERSION CABLE A 1 meter duplex multimode LC to SC conversion cable. . Used with the Quad OC3/STM1 SFP Cell Relay card or the OC3/STM1 Working I/O (90-9785-02) to adapt the SFP connector to existing cable connectors.

BNC CONVERSION CABLE FOR ELEC SFP A pair of 1 meter 1.0/2.3 Coaxial Connector (Type A Coupling) to BNC conversion cable. One can be used for Tx and the other for Rx. . Used with the Quad OC3/STM1 SFP Cell Relay card or the OC3/STM1 Working I/O (90-9785-02) to adapt the SFP connector to existing cable connectors.